Refine your search
Collections
Co-Authors
A B C D E F G H I J K L M N O P Q R S T U V W X Y Z All
Das, Probal Kumar
- Performance of a Newly Developed Multiwalled Carbon Nanotube Reinforced Alumina Tool Insert during Turning of AISI 1060 Steel
Abstract Views :592 |
PDF Views:3
Authors
Affiliations
1 Department of Mechanical Engineering, Kalyani Govt Engineering College, Kalyani-741235, IN
2 NOCCD, CSIR-Central Glass & Ceramic Research Institute, Kolkata–700032, IN
3 Department of Mechanical Engineering, Indian Institute of Technology, Kharagpur– 721302, IN
1 Department of Mechanical Engineering, Kalyani Govt Engineering College, Kalyani-741235, IN
2 NOCCD, CSIR-Central Glass & Ceramic Research Institute, Kolkata–700032, IN
3 Department of Mechanical Engineering, Indian Institute of Technology, Kharagpur– 721302, IN
Source
Journal of the Association of Engineers, India, Vol 86, No 1-2 (2016), Pagination: 64-79Abstract
Due to the demand of the manufacturing industry for high production-rate machining, ceramic tool material plays an important role. In this work, alumina (Al2O3) matrix composite reinforced with 0.3 vol.% multiwalled carbon nanotubes (MWCNTs) was prepared by hot-press sintering at a temperature of 1550°C under uniaxial load of 2.5 MPa. This developed nanocomposite having increased hardness, fracture toughness and flexural strength compared to monolithic Al2O3 was then used as a cutting tool insert with a nose radius of 1 mm for machining AISI 1060 steel rod under different machining conditions. Cutting force was measured and chip forms were observed at different levels of machining parameters to evaluate the machining performance of the tool insert. Results obtained from turning experiments show promising applicability of the developed 0.3 vol.% MWCNT/Al2O3 cutting tool insert.Keywords
Machining, Turning, MWCNT, CNT, Al2o3, Nanocomposite, Carbon Nanotube, Cutting Force, Machinability, Cutting Tool.
References
- Mondal, B., Chattopadhyay, A.B., Virkar, A. and Paul, A., Development and Performance of Zirconia-Toughened Alumina Ceramic Tools, Wear, Vol.156(2), pp.365-383, 1992.
- Mahanty, P.S., Mondal, B.N. and Das, S., Development and Performance Testing of Toughened Ceramic Alumina Cutting Tool, Proceedings of the International Conferences on Advanced Manufacturing Technology, Durgapur, India, pp.547-553, 2007.
- Dutta, A.K., Narasaiah, N., Chattopadhyay, A.B. and Ray K.K., Influence on Microstructure on Wear Resistance Parameter of Ceramic Cutting Tools. Materials and Manufacturing Processes, Vol.17(5), pp.651-670, 2002.
- Mandal, N., Doloi, B., Mondal, B. and Singh, B.K., Multi-Criteria Optimization and Predictive Modeling of Turning Forces in High-Speed Machining of Yittria Based Zirconia Toughened Alumina Insert Using Desirability Function Approach, Proceedings of Institute of Mechanical Engineers, Part B: Journal of Engineering Manufacture DOI: 0954405415596189, 2015.
- Senthil Kumar, A., Raja Durai, A. and Sornakumar, T., Machinability of Hardened Steel Using Alumina Based Ceramic Cutting Tools, International Journal of Refractory Metals & Hard Materials, Vol.21, pp.109–117, 2003.
- Yin, Z., Huang, C., Yuan, J., Zou B., Liu, H. and Zhu, H., Cutting Performance and Life Prediction of an Al2O3 /TiC Micro-Nano-Composite Ceramic Tool when Machining Austenitic Stainless Steel, Ceramic International, Vol.45(5), pp.7059-7065, 2015.
- Ko, Y.M., Won, W.T.K. and Kim, Y.W., Development of Al2O3–SiC Composite Tool for Machining Application, Ceramics International, Vol.30, pp.2081–2086, 2004.
- Lee, D.Y. and Yoon, D.H., Properties of Alumina Matrix Composites Reinforced with SiC Whisker and Carbon Nanotubes, Ceramics International, Vol.40, pp.14375–14383, 2014.
- Harris, P.J.F., Carbon Nanotube Composites, International Materials Reviews, Vol.49, pp.3143, 2004.
- Thostenson, E.T., Ren, Z. and Chou, T.W., Advances in the Science and Technology of Carbon Nanotubes and Their Composites: A Review, Composites Science and Technology, Vol.61, pp.1899–1912, 2001.
- Thomson, K.E., Jiang, D., Ritchie, R.O. and Mukherjee, A.K., A Preservation Study of Carbon Nanotubes in Alumina-Based Nanocomposites via Raman Spectroscopy and Nuclear Magnetic Resonance, Applied Physics. A, Vol.89, pp.651–654, 2007.
- Ahmad, K., Wei, P. and Wan, C., Thermal Conductivities of Alumina-Based Multiwall Carbon Nanotube Ceramic Composites, Journal of Material Science, Vol.49, pp.6048–6055, 2014.
- Xia, Z., Riester, L., Curtin, W.A., Li, H., Sheldon, B.W., Liang, J., Chang, B. and Xu, J.M., Direct Observation of Toughening Mechanisms in Carbon Nanotube Ceramic Matrix Composites, Acta Materialia, Vol.52, pp.931–944, 2004.
- Sarkar, S. and Das, P.K., Dry Sliding Wear Characteristics of Carbon Nanotube/ Alumina Nanocomposites under a Sharp Pyramidal Indenter, Ceramics International, Vol.40, pp.1397113978, 2014.
- An, J.W., You, D.H. and Lim, D.S., Tribological Properties of Hot-Pressed Alumina–CNT Composites, Wear, Vol.255, pp.677–681, 2003.
- Zhu, Y.F., Shi, L., Liang, J., Hui, D. and Lau, K., Synthesis of Zirconia Nanoparticles on Carbon Nanotubes and Their Potential for Enhancing the Fracture Toughness of Alumina Ceramics, Composites: Part B, Vol.39, pp.1136–1141, 2008.
- Bakhsh, N., Khalid, F.A. and Hakeem, A.S., Effect of Sintering Temperature on Densification and Mechanical Properties of Pressureless Sintered CNT-Alumina Nanocomposites, Materials Science and Engineering, Vol.60, pp.12-59, 2014.
- Liu, Y., Chae, H.G., Choi, Y.H. and Kumar, S., Effect of Carbon Nanotubes on Sintering Behavior of Alumina Prepared by Sol–Gel Method, Ceramics International, Vol.40, pp.65796587, 2014.
- Sarkar, S. and Das, P.K., Effect of Sintering Temperature and Nanotube Concentration on Microstructure and Properties of Carbon Nanotube/ Alumina Nanocomposites, Ceramics International, Vol.40, pp.7449–7458, 2014.
- Inam, F., Heaton, A., Brown, P., Peijs, T. and Reece, M.J., Effects of Dispersion Surfactants on the Properties of Ceramic–Carbon Nanotube (CNT) Nanocomposites, Ceramics International, Vol.40, pp.511–516, 2014.
- Hanzel, O., Sedlácek, J. and Sajgalík, P., New Approach for Distribution of Carbon Nanotubes in Alumina Matrix, Journal of the European Ceramic Society, Vol.34, pp.1845–1851, 2014.
- Zhang, T., Kumari, L., Du, G.H., Li, W.Z., Wang, Q.W., Balani, K. and Agarwal, A., Mechanical Properties of Carbon Nanotube–Alumina Nanocomposites Synthesized by Chemical Vapor Deposition and Spark Plasma Sintering, Composites: Part A, Vol.40, pp.86–93, 2009.
- Michálek, M., Sedlácek, J., Parchoviansky, M. and Michálková, M., Mechanical Properties and Electrical Conductivity of Alumina/MWCNT and Alumina/ Zirconia/ MWCNT Composites, Ceramics International, Vol.40, pp.1289–1295, 2014.
- Cha, S.I., Kim, K.T., Lee, K.H., Mo, C.B. and Hong, S.H., Strengthening and Toughening of Carbon Nanotube Reinforced Alumina Nanocomposite Fabricated by Molecular Level Mixing Process, Scripta Materialia, Vol.53, pp.793–797, 2005.
- Kumari, L., Zhang, T., Du, G.H., Li, W.Z., Wang, Q.W., Datye, A. and Wu, K.H., Thermal Properties of CNT-Alumina Nanocomposites, Composites Science and Technology, Vol.68, pp.2178–2183, 2008.
- Lee, D.Y. and Yoon, D.H., Properties of Alumina Matrix Composites Reinforced with SiC Whisker and Carbon Nanotubes, Ceramics International, Vol.40, pp.14375–14383, 2014.
- Dhar, N.R., Ahmed, M.T. and Khoda, A.K.M.B., Analysis of Influence of Machining Time and Tool Wear on Surface Roughness in Turning AISI-1060 Steel, Proceedings of the International Conference on Mechanical Engineering 2007, Dhaka, Bangladesh, pp.ICME07AM-37:1-5, 2007.
- Paul, S., Dhar, N.R. and Chattopadhyay, A.B., Beneficial Effects of Cryogenic Cooling over Dry and Wet Machining on Tool Wear and Surface Finish in Turning AISI 1060 Steel, Journal of Materials Processing Technology, Vol.116, pp.44-48, 2001.
- Kamruzzaman, M. and Dhar, N.R., Effect of High-Pressure Coolant on Temperature, Chip, Force, Tool Wear, Tool Life and Surface Roughness in Turning AISI 1060 Steel, G.U. Journal of Science, Vol.22(4), pp.359-370, 2009.
- Sarkar, S. and Das, P.K., Processing and Properties of Carbon Nanotube/ Alumina Nanocomposites: a Review, Reviews on Advanced Materials Science, Vol.37(1/2), pp.53-82, 2014.
- Khan, M.M.A. and Dhar, N.R., Performance Evaluation of Minimum Quantity Lubrication by Vegetable Oil in Terms of Cutting Force, Cutting Zone Temperature, Tool Wear, Job Dimension and Surface Finish in Turning AISI-1060 Steel, Journal of Zhejiang University Science A, Vol.7(11), pp.1790-1799, 2006.
- Carou, D., Rubio, E.M., Lauro, C.H. and Davim, J.P., Experimental Investigation on Surface Finish during Intermittent Turning of UNS M11917 Magnesium Alloy under Dry and Near Dry Machining Conditions, Measurement, Vol.56, pp.136–154, 2014.
- Palanikumar, K. and Muniaraj, A., Experimental Investigation and Analysis of Thrust Force in Drilling Cast Hybrid Metal Matrix (Al–15% SiC–4% Graphite) Composites, Measurement, Vol.53, pp.240–250, 2014.
- Karpuschewski, B., Schmidt, K., Beno, J., Mankova, I. and Prilukova, J., Measuring Procedures of Cutting Edge Preparation when Hard Turning with Coated Ceramics Tool Inserts, Measurement, Vol.55, pp.627–640, 2014.
- Mishra, V., Khan, G.S., Chattopadhyay, K.D., Nand, K. and Sarepaka, R.V., Effects of Tool Overhang on Selection of Machining Parameters and Surface Finish during Diamond Turning, Measurement, Vol.55, pp.353–361, 2014.
- Senthilkumar, N., Tamizharasan, T. and Anandakrishnan, V., Experimental Investigation and Performance Analysis of Cemented Carbide Inserts of Different Geometries Using Taguchi Based Grey Relational Analysis, Measurement, Vol.58, pp.520–536, 2014.
- Bhattacharya, A., Das, S., Majumder, P. and Batish, A., Estimating the Effect of Cutting Parameters on Surface Finish and Power Consumption during High Speed Machining of AISI 1045 Steel Using Taguchi Design and ANOVA, Production Engineering; Research and Development, Vol.3, pp.31–40, 2009.
- Sarkar, S., Sarkar, S., Das, P.K., Das, S. and Paul, S., Force Measurement during Turning of AISI 1060 Steel with CNT/Alumina Insert, Proceedings of the 1st International Conference on Emerging Materials: Characterization & Application, Jadavpur, Kolkata, India, p.114, 2014.
- Michálek, M., Sedlácek, J., Parchoviansky, M., Michálková, M. and Galusek, D., Mechanical Properties and Electrical Conductivity of Alumina/ MWCNT and Alumina/ Zirconia/ MWCNT Composites, Ceramics International, Vol.40, pp.1289-1295, 2014.
- An Experimental Investigation on Surface Roughness Achieved During Abrasive Water-Jet Machining of Low Carbon Steel
Abstract Views :356 |
PDF Views:7
Authors
Affiliations
1 Department of Mechanical Engineering, Kalyani Government Engineering College, Kalyani-741235, West Bengal, IN
2 CSIR-Central Glass and Ceramic Research Institute, Jadavpur, Kolkata-700032, IN
1 Department of Mechanical Engineering, Kalyani Government Engineering College, Kalyani-741235, West Bengal, IN
2 CSIR-Central Glass and Ceramic Research Institute, Jadavpur, Kolkata-700032, IN
Source
Journal of the Association of Engineers, India, Vol 87, No 1-2 (2017), Pagination: 26-32Abstract
In Abrasive Water Jet Machining (AWJM), abrasive particles suspended in high pressure water are impinged on work surface for removal of excess materials. A nozzle is fitted in front of workpiece to provide high velocity jet. In this work, appropriate machining condition is tried to evaluate to yield minimum surface roughness by employing Response Surface Methodology (RSM) while machining low carbon steel. Radius of curvature is also observed during abrasive water jet machining. A statistical model is generated for predicting surface roughness. It is observed that at low feed rate condition, better surface is obtained expectedly.Keywords
Abrasive Water Jet Machining, AWJM, Optimisation, Response Surface Methodology, RSM, Surface Roughness.References
- Singh, P.J., Relative performance of abrasives in abrasive waterjet cutting, Proceedings of the 12th International Conference on Jet Cutting Technology, Rouen, France, pp. 521-541, 1994.
- Vasek, J., Martinec, P., Foldyna, J. and Hlavac, L., Influence of properties of garnet on cutting process, Proceedings of the 7th Water Jet Conference, America, pp. 375-387, 1993.
- Ives, L.K. and Ruff, A.W., Electron microscopy study of erosion damage in copper, Special Technical Publication, Am. Soc. Test. Mater, Vol. 664, pp. 5-35, 1977.
- Armada, S., Hirose, T. and Senda, T., Quantitative evaluation of residual grits under angled blasting, Surface (Coating) Technology, Vol. 111, pp. 1-9, 1999.
- Chen, F.L., Siores, E., Patel, K. and Momber, A.W., Minimising particle contamination at abrasive water jet machined surfaces by a nozzle oscillation technique, International Journal of Machine Tools and Manufacture, Vol. 42, pp. 1385-1390, 2002.
- Ojmertz, K.M.C., Abrasive water jet milling: an experimental investigation, Proceedings of the 7th US Water Jet Conference, Water Jet Technology Association, St. Louis, pp. 777-791, 1993.
- Hashish, M., Controlled depth milling of isogrid structures with AWJ, Journal of Manufacturing Science and Engineering, Vol. 120, pp. 21-27, 1998.
- Hashish, M., Milling with abrasive water jets: a preliminary investigation, Proceedings of the 4th US Water Jet Conference, ASME, New York, pp. 1-10, 1987.
- Ojmertz, K.M.C., Analysis of surfaces produced by abrasive water jet milling techniques, Jet Cutting Technology, Mechan. Engng Publishers, Bury, St Edmunds, pp. 753-768, 1996.
- Knapp, M. and Ohlsen, J., Recycling of abrasive material in water jet cutting, Proceedings of the 12th International Conference on Jet Cutting Technology, Rouen, France, pp. 511-519, 1994.
- Ohman, J.L., Abrasives: their characteristics and effect on water jet cutting, Proceedings of the Seventh American Water Jet Conference, WJTA, Seattle, WA, pp. 363-374, 1993.
- Hashish, M., Pressure effect in AWJ machining, Jornal of Engineering. Mater. Technol. Vol. 3, pp. 221-228, 1989.
- Sasikumar, K.S.K. Arulshri, K.P., Ponappa1, K. and Uthayakumar, M., A study on kerf characteristics of hybrid aluminium 7075 metal matrix composites machined using abrasive water jet machining technology, Proceedings of IMechE, Part B: J Engineering Manufacture, 2016, DOI: https://doi.org/10.1177/0954405416654085.
- Jagdale, S., Dhanawade A. and Kumar S., An experimental study of influence of process parameters on kerf properties of abrasive water jet machined carbon fibre reinforced polymer, Journal of the Association of Engineers, India, Vol. 86 (1 & 2), pp. 15-22, 2016.
- Bose, P., Dhanawade A. and Kumar S. Experimental study of glass fibre reinforced polymer surfaces machined by abrasive water jet machining, Journal of the Association of Engineers, India, Vol. 86 (3 & 4), pp. 35-44, 2016.